ronaldweinland.info Readers ASTM E1886 PDF

ASTM E1886 PDF

Friday, April 19, 2019 admin Comments(0)

laminated glazing systems must resist the cyclic pressure tests of ASTM E1886. Polycarbonate glazing systems are also used in place of traditional laminated. 3.3 Compliance Statement: Results obtained are tested values and were secured by using the designated test methods. The specimens tested met the. ASTM E1886-05, Standard Test Method for Performance of Exterior Windows, Curtain. Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and .


Author:ELOIS BALANOFF
Language:English, Spanish, Indonesian
Country:Austria
Genre:Technology
Pages:422
Published (Last):15.06.2015
ISBN:569-4-65706-486-3
ePub File Size:22.37 MB
PDF File Size:13.51 MB
Distribution:Free* [*Register to download]
Downloads:32759
Uploaded by: TESS

E1886-13a Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, Standard + Redline PDF Bundle ASTM License Agreement. This standard is issued under the fixed designation E 1886; the 1 This test method is under the jurisdiction of ASTM Committee E06 on. 3.1 Product Type: Sliding Door. 3.2 Series/Model: 3070-HI. 3.3 Compliance Statement: Results obtained are tested values and were secured by.

Does it really work? It really does! Want to see for yourself? How strong is AstroGuard? And, with a burst strength of well over 1500 lbs,, AstroGuard easily outranks metal panels, roll-downs, accoridons, and other traditional hurricane systems. Is it expensive?

ForceFront Storm™ E44000 Storefront - Wausau Window

The largest size maximum area, height, and width of exposed light of the light kit and the minimum stile and rail dimensions shall be defined. The ratings for such assemblies shall indicate design pressure for the assembly both with and without the additional hardware. At the discretion of the test sponsor the same or an identical assembly shall be permitted for the structural test.

For doors designated by the manufacturer as either in-swing only or out-swing only, the impact test shall be conducted only from the outdoor side of the assembly.

ASTM E1886-13a

For doors designated as either in-swing or out-swing, the impact tests shall be conducted from the outside push side of in-swinging assemblies on two samples and from the outside pull side of an out-swinging assembly on the third sample.

These door types shall have been qualified to receive light kits in accordance with paragraph 8. Glazing systems shall include all parts necessary to install the glazing in the door. This shall normally include at least a glazing panel, frame, sealant or glazing compound and fasteners.

Popular Publishers

In this case, the largest size maximum area, height, and width of exposed light of the light kit and the minimum stile and rail dimensions shall be defined. Three identical assemblies are required. The doors shall be mounted in frames and bucks as required for the standard door test procedure. Frames for these assemblies shall be evaluated for installation in each wall type for which the product is intended.

You might also like: ASTM D4945 PDF

Installation instructions shall include: glazing material, sealants or glazing compounds, installation procedures, and details of frame anchoring methods. Doors used for this test shall be stiffened as described in section 5.

E1886 pdf astm

Doors are to be equipped with rim exit devices or other hardware as specified by the manufacturer 11. The pressure load shall be maintained for a minimum of 30 seconds.

One impact is to be applied at the meeting edge of the doors 6 inches down from the head jamb. The second impact is to be applied at the meeting edge of the doors 6 inches up from the sill and the third impact applied at the centerline of the latch and 6 inches horizontally from the latch edge of the door.

E1886 pdf astm

The missiles and their associated velocity ranges used in this test method are selected to reasonably represent typical debris produced by windstorms. Superimposed on the averaged winds are gusts whose aggregation, for short periods of time ranging from fractions of seconds to a few seconds may move at considerably higher speeds than the averaged winds. Wind pressures related to building design, wind intensity versus duration, frequency of occurrence, and other factors are considered.

Safety Testing Summary

It is appropriate to test the strength of the assembly for a time duration representative of sustained winds and gusts in a windstorm. Gust wind loads are of relatively short duration.

Other test methods, such as Test Methods E330 and E1233, do not model gust loadings. They are not to be specified for the purpose of testing the adequacy of the assembly to remain unbreached in a windstorm environment following impact by windborne debris. Scope 1.

A missile propulsion device, an air pressure system, and a test chamber are used to model some conditions which may be representative of windborne debris and pressures in a windstorm environment. This test method is applicable to the design of entire fenestration or impact protection systems assemblies and their installation. The performance determined by this test method relates to the ability of elements of the building envelope to remain unbreached during a windstorm.

Values given in parentheses are for information only.

Pdf astm e1886

Certain values contained in reference documents cited herein may be stated in inch-pound units and must be converted by the user. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Specific hazard statements are given in Section 7. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Facades ; 91.